Difference between revisions of "Xbox Linux Issues"

Revision as of 01:48, 30 June 2022

Here is a list of issues that are blocking general functionality on Xbox Linux.

XBPartitioner Table and MBR incompatibility

This issue is relevant to native Linux installs. In a native Linux install, the user formats empty regions of their hard drive and adds an MBR to the hard drive, which is used by Cromwell to access the Linux boot partition and subsequently load linuxboot.cfg, the kernel, and the initrd. The way that Cromwell is currently set up, it can't find Linux partitions without the MBR.

The MBR partitioning/boot scheme uses a 512 byte record at the beginning of the drive. Since the actual boot data isn't needed on Xbox, the first 440 bytes are filled with zeroes when using fdisk, and can be considered unused here. [layout information]

The FATX filesystem has a config area of 1024 bytes starting at the beginning of the drive. Only 48 bytes are officially used; the rest are zeroes. On a stock-formatted Xbox hard drive, the contents of this config area don't seem to matter much to ind-BIOS (tested), although Insignia may use it in the future. If a stock FATX config area has its first 512 bytes overwritten by an MBR, it is not known to cause problems with any other Xbox functionality. (based on the fact that native Linux installs have been run in this way for years)

The problem arises with the XBPartitioner table, a custom partitioning scheme for Xbox hard drives that was never officially supported by Xbox Linux. The XBPartitioner table provides 14 partition "slots" for FATX partitions. The partition table is written into unused space in the FATX config area. XBPartitioner wipes the remaining bytes of the config area when writing a partition table including any MBR contents; other tools are untested so far. And fdisk overwrites the first 512 bytes of the FATX config area with an MBR, replacing the first 440 bytes with zeroes.

Another issue arises in that the two partitioning schemes overlap, even if only the necessary data were written for both XBPartitioner table and MBR; that is if they didn't write the zeroes.

This struct shows the layout of the config area, followed by the partition entry struct. From the unofficial XBPartitioner patches for the old Xbox kernel:

// Temporary struct used to load XBPartitioner data directly from disk.
typedef struct {
	char                 magic[16];
	char                 reserved[32];
	XBPartitionerTableEntry partitions[FATX_XBPARTITIONER_PARTITIONS_MAX];
} XBPartitionerTable;

// Temporary struct used to load XBPartitioner data directly from disk.
typedef struct
{
	char name[16];
	u32  flags;
	u32  start;
	u32  size;
	u32  reserved;
} XBPartitionerTableEntry;

The XBPartitioner table entries start at 48 bytes, and each partition's entry is 32 bytes in size. With 14 partitions, the XBPartitioner table ends at 496 bytes, and overwrites a good chunk of the relevant MBR content, which starts at 440 bytes. So tool modification alone can't make these schemes compatible.

The XBPartitioner table has no metadata, only partition entries, and has no known way of redefining the number of available partitions. However, if the XBPartitioner table only had 12 partitions, the partition table would end at 432 bytes and the two schemes could coexist.

Possible Solutions

F Takes All

This was the typical scheme used by historical Xbox Linux. The area after E would be used for Linux partitions. With larger hard drives available, there is a need for Xbox Linux to coexist with other content on the user's drive. This is okay when the user doesn't want to later modify the partition layout of their hard drive using XBPartitioner, and they want to reserve that hard drive primarily for Linux.

A 12 partition XBPartitioner Table

This would involve attempting to get general acceptance of changing the XBPartitioner spec to 12 partitions, so it doesn't overlap with MBR. Or providing a custom set of tools and bioses that support this. Pros

• Cromwell would not need to be modified
• The 512 byte boundary could be considered the starting point for future config area modifications
• Very few users have more than 7, much less 14 partitions on their Xbox which provide little practical use
• Any Linux PC can easily mount the Linux partitions

Cons

• Lots of software would need to be updated, including BIOSes, partitioning tools, and disk formatting tools in Xbox Linux and on PC. There might be a more elegant solution.

Using the XBPartitioner Table To Define Linux Partitions

Pros

• No partitioning scheme incompatiblity management
• No dual partitioning scheme; both Linux and Xbox tools would have awareness of the full drive partition table, to avoid accidentally creating overlapping partitions
• Unused per-partition flags in the XBPartitioner table could be used to mark partitions as Linux as a future standard
• Scripts utilizing dd to read the XBPartitioner table could be used as a stopgap before full kernel support is developed

Cons

• The Cromwell Grub code would need to be modified to use the XBPartitioner table in place of MBR (this may not be overly complicated)
• Scripts, tools, or kernel support will be needed in order to mount these partitions in Linux, both on the Xbox and on other PCs
• Any tools used to mount Linux partitions and edit their characteristics would have to be updated to support it, primarily apps that mount non-FATX partitions. This could be simple
• FATX kernel support would need to be ported for a long term performant solution, but fatxfs performance still needs to be evaluated on Xbox.
• The user is limited to 14 total partitions; with F and G they have 7 partitions which is enough for 3 Linux installs (3 boot partitions, 3 data partitions, and shared swap). It would be workable though for most use cases.

Lack of FATX Kernel Support

Loop devices are a common method of packaging Xbox Linux installations, in order to avoid modifying the partition table on the Xbox hard drive. A loop device is a filesystem image that can be mounted from within another filesystem. When put on a FATX partition, they allow Xbox Linux to be run from the hard drive without modifying the user's partition table at all. These setups can be used to bundle Linux builds and other apps for easy distribution. (XMugen, for instance.)

The current Xbox Linux patches don't port over the support for mounting the FATX filesystem in Linux. This is because the underlying code has changed significantly in a few places since then. User:VannevarKush is working on porting the old FATX code to the kernel for native support, but it is a work in progress.

The lack of native FATX support means that mounting loop devices can't be done. Right now, native install and live CDs are the current available boot options for Xbox Linux.

The FUSE based fatxfs code by mborgerson may be usable as a stopgap, although its performance hasn't been evaluated yet on an Xbox.

Advanced Video Support

The Xbox Linux kernel currently only uses the most basic video support available (defined by CONFIG_FRAMEBUFFER_SIMPLE in the kernel config). More advanced support may be needed to run desktop environments and to run graphical applications with better performance. Does code need to be merged over from the original sources for xbox video?