Difference between revisions of "Super I/O"
From xboxdevwiki
(→U1 SMsC LPC ic: updates for pins 27,40, 44,45 and 60 (pins RX and TX on MAX223)) |
|||
| Line 76: | Line 76: | ||
|J9 pin 3 | |J9 pin 3 | ||
|LFrame | |LFrame | ||
| + | |- | ||
| + | |U1 p27 | ||
| + | |R7 | ||
| + | |Pull up (3.3v) | ||
|- | |- | ||
|U1 p29 | |U1 p29 | ||
| Line 84: | Line 88: | ||
|J9 pin 16 | |J9 pin 16 | ||
|(unkown function) | |(unkown function) | ||
| + | |- | ||
| + | |U1 p40 | ||
| + | |GND | ||
| + | | | ||
| + | |- | ||
| + | |U1 p44 | ||
| + | |3.3v with C2 | ||
| + | |Vcc? | ||
| + | |- | ||
| + | |U1 p45 | ||
| + | |R1 (R2 unpopulated) | ||
| + | |Pull down (R2 would be pullup 3.3v) | ||
| + | |- | ||
| + | |U1 p60 | ||
| + | |GND | ||
| + | | | ||
|- | |- | ||
|U1 P84 | |U1 P84 | ||
| − | |U3 | + | |U3 P8 |
|RX | |RX | ||
|- | |- | ||
|U1 P85 | |U1 P85 | ||
| − | |U3 | + | |U3 P6 |
|TX | |TX | ||
|} | |} | ||
Revision as of 20:11, 6 February 2018
The Super I/O board is a feature of some Development Kits. The board is build around a SMSC LPC47M157 chip (Datasheet) and interfaces with the Xbox via a ribbon cable connected to the LPC Debug Port.
The board provides the following ports:
- RS232 (used for Kernel debugging, not to be confused with Xbox Debug Monitor)
unpopulated ports or functions are:
- PS/2 Mouse port[citation needed]
- PS/2 Keyboard port[citation needed]
- something MCPX (SMBus?)[citation needed]
- Temp something (SMBus?)[citation needed]
- Post code (SMBus?)[citation needed]
- Flash-ROM / BIOS (like modchips, replaces onboard kernel?)[citation needed]
Picture of the board[FIXME]
Schematic
Its a four layer board, layers 2 and 3 are filled on the entire board, probably ground and power planes. north, or up in the next tables is up as written the layer numbers and silkscreen common direction. The folowing main parts are populated on the board:
| total | Labels | Description |
|---|---|---|
| 1 | U1 | SMSC LPC47M157-NC (1996 ) |
| 1 | U3 | MAX223EAI (0104, first week 2004?) |
| 1 | Y2 | CMX-309FB B (14.3181Mhz standard Clock Oscillator ) |
| 1 | J7 | AMP rs232 Male connector |
| 1 | J9 | 16 pins male header (LPC bus) |
| 5 | R1,R7,R10,R11,R12 | 10Kohm smd resistor |
| 7 | C10,C12,C13,C16,C17,C36,C37 | Bigger, probably NOT all the same caps |
| 17 | C1,C2,C9,C15,C1?(8?),C21,C22,C23,C24,C25,C26,C28,C31,C32,C33,C34,C35 | Smaller, also, asuming not all the same |
The connections in the following tables are checked with the continuity test on a VOM(Multimeter). but for now here are the listings of wich pin goes where:
U1 SMsC LPC ic
| Pin | to pin | Note |
|---|---|---|
| U1 pin 18 | C17(up) and ? | (not finished) |
| U1 pin 6,7 | C17(down) and GND | Both U1 pins yes) |
| U1 p24 | J9 pin 3 | LFrame |
| U1 p27 | R7 | Pull up (3.3v) |
| U1 p29 | J9 pin 1 | LClk |
| U1 p30 | J9 pin 16 | (unkown function) |
| U1 p40 | GND | |
| U1 p44 | 3.3v with C2 | Vcc? |
| U1 p45 | R1 (R2 unpopulated) | Pull down (R2 would be pullup 3.3v) |
| U1 p60 | GND | |
| U1 P84 | U3 P8 | RX |
| U1 P85 | U3 P6 | TX |
J9 LPC header
Not finished
| Pin | to pin | Note |
|---|---|---|
| J9 pin 1 | U1 p29 | |
| J9 pin 2 | GND | |
| J9 pin 3 | U1 p24 | LFrame |
| J9 pin 4 | NC | no pin |
| J9 pin 5 | RST | |
| J9 pin 6 | C12(e),C13(S),C15(S),U3 p11. | 5V |
| J9 pin 7 | LAD3 | |
| J9 pin 8 | LAD2 | |
| J9 pin 9 | 3.3V | |
| J9 pin 10 | LAD1 | |
| J9 pin 11 | LAD0 | |
| J9 pin 12 | GND | |
| J9 pin 13 | U1 p104 | SCL |
| J9 pin 14 | U1 p103 | SDA |
| J9 pin 15 | 3.3V | |
| J9 pin 16 | U1 p30 | (unkown function) |
Related links
(SMBus?)
