Difference between revisions of "Power Supply"

Revision as of 09:51, 31 August 2017

It's either a Foxlink^{[citation needed]} or Delta Electronics power supply for most xboxes. Some are rumoured to be shipped with a Minebea brand and 1.6 xboxes are found with a "tuscany" made probably by Samsung.

On a 1.0 xbox supply, there seems to be 2^{[citation needed]} types for the US 120V and EU 240V market.

The standby voltage powers the SMC which handles turning on and off the system. The Xbox supply needs a voltage (3V3?) on it's power-on line to leave the standby mode. This results in the other voltages being supplied.

Delta Electronics

The marks are on the PCB with a check next to them:

• Delta Electronics DPSN-96-AP-1 should be the EU 240V one^{[citation needed]}
• Delta Electronics DPSN-96-AP is the US 120V one

There is a link J11 under CR1 (right side of the coil under it) that might make the difference between 120V and 240V. It also seems that the Bridge rectifier is bigger on the US models. This could make sense as it has to handle double the current. So, before experimenting with this it might be worth to check if the installed type can handle 2.3 amps.

The rated output currents are also noted on the PCB

• 3V3 Standby 0.075A
• 3V3 4.8A
• 5V 13.2A
• 12V 1.2A

Foxlink Technology LTD

^[FIXME]On the lower heatsink, there is a sticker with the following markings and versions:

• MODEL: FTPS-0001 REV:B {citation needed} (120V)
• MODEL: FTPS-0002 REV:B (from a 2002 PAL (240V))
• MODEL: FTPS-0002 REV:H (from a 2003 PAL (240V))
• MODEL: FTPS-0002 REV:G {citation needed} (240V)
• MODEL: FTPS-0007 REV:B {citation needed} (120V) (are these after the powercord recall?)
• MODEL: FTPS-0007 REV:D {citation needed} (120V) (are these after the powercord recall?)

The rated output currents are also noted on the sticker

• 96W Max output power
• 3V3 Standby 0.045A
• 3V3 4.8A
• 5V 13.2A
• 12V 1.2A

power cord recall

Microsoft started an powercord recall, or more like a replacement program xbox.comfor what apeared to be Foxlink powersupplies having a bad powerplug connector on the back of the console and where installed in 1.0 and 1.1 xboxes.{citation needed}.

Does my console require a replacement cord?
If it was manufactured before October 23, 2003, your console requires a replacement cord (except for consoles purchased in Continental Europe, where consoles manufactured prior to January 13, 2004 require a replacement cord). Consoles manufactured after October 23, 2003 (after January 13, 2004 for consoles purchased in Continental Europe) do not require replacement cords because design improvements to the cord and console already protect against the problems that are addressed by the replacement cords.

source: Xbox powercord recall program faq

Microsoft tried to resolve this by offering free replacement powercords and advising to trow out the old ones. More to the power cord replacement than meets the eye?. The old page describing how to order has been archived here: [1] One would either recieve a thicker but very similiar powercord or an actual GFI (Ground Fault Circuit Interupter). a online form would then be used to determine wich type of cable you recieve by means of serial number. ^[FIXME]

An more in detail video of whats inside an european (UK) "AFCI" [2]

AFCI

An european AFCI ordered from MS for free had the following on the bottom label.

The cable that is wired to the AFCI has the following markings:

Old and New cords

The replacement cable has the following markings:^{[citation needed]}

The older cable that needed replacement was:

Presumely this one doesnt come with tighter tolerances.

Samsung "TUSCANY"

Found in 1.6 xboxes and seems to be made by Samsung (or atleast the main transformer is, wich also has the detail label on it) ^[FIXME]

• PSCD101301A

Minebea

^[FIXME]

• MS001A096EMJ

Connector pinout

Xbox 1.0 and 1.1

Xbox 1.2 and later

Related links

• Describes how to turn an ATX Power-Supply to Xbox PSU
• Powercord recall blog with exacter cable numbers