Super I/O

From xboxdevwiki
Revision as of 06:30, 13 February 2018 by Ernegien (talk | contribs) (Related links)
Jump to: navigation, search

The Super I/O board is a feature of some Development Kits. The board is build around a SMSC LPC47M157 chip (Datasheet) and interfaces with the Xbox via a ribbon cable connected to the LPC Debug Port.

The board provides the following ports:

unpopulated ports or functions are:

Picture of the board[FIXME]

Schematic

Its a four layer board, layers 2 and 3 are filled on the entire board, probably ground and power planes. north, or up in the next tables is up as written the layer numbers and silkscreen common direction. The folowing main parts are populated on the board:

total Labels Description
1 U1 SMSC LPC47M157-NC (1996 )
0 U2 unpopulated DIP24 MCU(?)
1 U3 MAX223EAI (0104, first week 2004?)
1 Y2 CMX-309FB B (14.3181Mhz standard Clock Oscillator )
1 J7 AMP rs232 Male connector
1 J9 16 pins male header (LPC bus)
5 R1,R7,R10,R11,R12 10Kohm smd resistor
7 C10,C12,C13,C16,C17,C36,C37 Bigger, probably NOT all the same caps
17 C1,C2,C9,C15,C1?(8?),C21,C22,C23,C24,C25,C26,C28,C31,C32,C33,C34,C35 Smaller, also, asuming not all the same

The connections in the following tables are checked with the continuity test on a VOM(Multimeter). but for now here are the listings of wich pin goes where:

U1 SMsC LPC ic

Pin to pin Note
U1 pin 18 C17(up) and ? (not finished)
U1 pin 6,7 C17(down) and GND Both U1 pins yes)
U1 p24 J9 pin 3 LFrame
U1 p27 R7 Pull up (3.3v)
U1 p29 J9 pin 1 LClk
U1 p30 J9 pin 16 (unkown function)
U1 p40 GND
U1 p44 3.3v with C2 Vcc?
U1 p45 R1 (R2 unpopulated) Pull down (R2 would be pullup 3.3v)
U1 p60 GND
U1 P84 U3 P8, U2 P18 RX
U1 P85 U3 P6, U2 P17 TX

J9 LPC header

NOTE: version 1.3+ motherboards are missing the LFRAME signal which will need to be generated by an external CPLD [1]

NOTE: version 1.5 motherboards are missing pins 2 (GND) and 9 (VCC3), and pins 12 (GND) and 15 (VCC3) haven't been confirmed to work correctly[citation needed]

Pin Name Type Description Termination(s) Notes
1 LCLK Output PCI clock U1 29
2 VSS Power System ground (see other parts)
3 LFRAME# Output Frame signal U1 24 Indicates start of a new cycle and termination of broken cycle.
4 --- --- --- --- Voided to ensure correct ribbon cable alignment.
5 LRST# Output PCI reset U1 26 Used as LPC interface reset.
6 VCC5 Power 5V power supply (see other parts) C12(e), C13(S), C15(S), U3 11
7 LAD3 I/O LPC address/data bus U1 23 Multiplexed command, address and data bus.
8 LAD2 I/O LPC address/data bus U1 22 Multiplexed command, address and data bus.
9 VCC3 Power 3.3V power supply (see other parts)
10 LAD1 I/O LPC address/data bus U1 21 Multiplexed command, address and data bus.
11 LAD0 I/O LPC address/data bus U1 20 Multiplexed command, address and data bus.
12 VSS Power System ground (see other parts)
13 SCL I/O SMBus clock signal U1 104
14 SDA I/O SMBus data signal U1 103
15 VCC3 Power 3.3V power supply (see other parts) Intended to be used for external IO board
16 L_SER_IRQ Input Serial interrupt requests U1 30 Provides a serial interrupt request line for mouse/keyboard implementations of the IO board.

Related links

(SMBus?)