Manufacturing Process

From xboxdevwiki
Revision as of 03:18, 29 December 2017 by Furon (talk | contribs) (Mention Taiwan)
Jump to: navigation, search
Sárvár, Hungary factory

The Xbox was manufactured in four locations throughout its lifetime: Guadalajara, Mexico; Sárvár, Hungary; Doumen, China; and Taiwan[FIXME].

Serial Number

An example of a serial number sticker

Every Xbox has a sticker on the bottom with a manufacturing date and a 12-digit serial number. The serial number encodes information about where and when the hardware was manufactured.

Using the pictured serial number as an example:

Line Number Year Week Factory
1 166356 2 09 03

The first field is the factory production line number. The second field is the Xbox's number for the week (for the whole factory, not just the one line). The third field is the last digit of the year. The fourth field is the week of the year. Finally, the fifth field is the factory number. Mexico is 02, Hungary is 03, China is 05, and Taiwan is 06.

So this Xbox was the 166,356th to be manufactured in week 9 of the year 2002 on production line 1 in Sárvár, Hungary.

Timeline

Mexico Hungary China
2001
October Production of 110V 1.0 Xboxes with Thomson DVD drives begins for USA/Canada.
2002
January Production begins for Japan. Production switches to 220V 1.0 models for Europe/Australia.
April Production lines 1 and 6 are moved to China. 50% of new units now produced with Philips DVD drives. [FIXME]
May Production stops after ~3 million units. All four production lines moved to China.
August Production of the 220V 1.1 Xbox for Europe/Australia begins, with mostly Philips and sometimes Thomson DVD drives.
September Most units now use Samsung DVD drives.
October Remaining four lines switched to version 1.1.
November Production extended to 110V USA/Canada/Japan models.
December Production ends after ~7 million units. First line changes to version 1.2.
2003
February Last line changes to version 1.2.
March First line changes to version 1.3.
April Last line changes to version 1.3.
July First line changes to version 1.4.
August First line changes to version 1.5.
2004 [FIXME]
 ?  ?

Hardware assembly

The Xbox was manufactured just like many other mass-produced electronic products. Printed circuit boards were made in bulk and populated by pick-and-place machines, the plastic case was formed by injection molding, and finally all of the pieces were assembled by hand on production lines.

The overall process didn't vary much between hardware revisions. The only notable change was related to the BIOS ROM. Up until version 1.6, the BIOS was flashed onto a TSOP ROM before being soldered to the motherboard. Revision 1.6 introduced the Xyclops chip, which integrated both the System Management Controller and the BIOS ROM on a single die. This meant the BIOS had to be flashed by the chip manufacturer instead of on the Xbox production line.

Software initialization

When a fully-assembled Xbox reached the end of the production line, it had a:

  • valid BIOS image
  • blank EEPROM
  • blank, unlocked hard disk

To initialize the EEPROM and hard disk in the final stage of production, a technician would insert a DVD containing a setup program. The setup program, named default.xbe just like any other primary Xbox executable, was built by the XDK with the "allow eject" flag set and the region code set to 0x80000000 ("DEBUG").

When the Xbox kernel initializes, it checksums the EEPROM. If it fails, the Xbox will be in DEBUG mode, i.e. the region code is set to 0x80000000. With the region code set to this value, the kernel ignores it if the hard disk is not locked. Because the region code matches, the kernel will run the executable from the DVD, which does the following:

  1. Format the three swap partitions
  2. Copy XMTAXBOX.XBE from the DVD to the first cache partition and run it

Then the DVD can be ejected and put into the next Xbox.

XMTAXBOX.XBE

This XMTAXBOX.XBE is an XBE retail-signed for hard disk, also with the region code set to 0x80000000, that does the following:

  1. Retrieve the EEPROM contents from a network server
  2. Retrieve the contents of the system and data partitions from a network server
  3. Lock the hard disk
  4. Run some self tests and send a report to the server

A new Xbox still contains the file XMTAXBOX.XBE on the first cache partition, as well as some temporary files on the third one.

Xbox kernels since version 4034 have another backdoor that even works if the EEPROM check succeeds: If bit 30 of the media flag of an XBE is set, the condition of the hard disk is ignored as well. This change allows Microsoft to replace broken hard disks without replacing a valid EEPROM on an Xbox sent in for repair. Before this change, they had to rewrite the EEPROM whenever they replaced the drive.

Packing and shipping

Credits

This article is adapted from Xbox Manufacturing Process by Michael Steil. Its content is reproduced here under the GNU Free Documentation License 1.2.

Production line photos are from Andy Rostad's gallery.