Boot Process

From xboxdevwiki
Revision as of 08:43, 30 August 2017 by KaosEngineer (talk | contribs) (Stage 1: Key Scheduling: Address range for s[] incorrect 0x8F000 to 0x850FF should be 0x8F000 to 0x8F0FF)
Jump to: navigation, search

This article describes the boot sequence of the Xbox. A large portion of it is patended in Patent "US 6,907,522 B2"

Overview

The Xbox has a 256 kiB ROM containing the startup animation and sound, as well as the Xbox kernel, which contains a stripped down version of the Windows 2000 (NT 5.0) microkernel, the HAL, filesystems, as well as HDD and DVD drivers.

When the Xbox is turned on, the software in ROM is decompressed into RAM, and the kernel initializes the hardware. Because there are no audio or video drivers in the kernel, the startup code plays the animation and sound by accessing the registers of the hardware directly. As soon as the Xbox logo is on the display, the kernel unlocks the hard disk and checks whether there is a valid game medium in the DVD drive. If not, the file xboxdash.xbe gets loaded from partition #3 (Typically the Dashboard). In either case, the Microsoft logo is shown below the Xbox logo and the executable is started. If an error occurs (no/wrong hard disk, wrong signature, ...), the boot loader shows a Fatal Error screen and halts.

Chain of trust

The Xbox uses a chain of trust during the boot process:

  • The MCPX ROM contains a key to decrypt the 2BL.
  • The 2BL is run. The MCPX ROM is hidden at this point. The 2BL decryption key is (overwritten with 0x00-Bytes)[FIXME]. The 2BL contains a kernel decryption key.
  • Once the kernel is decrypted and initialized, the INIT section is discarded. The kernel decryption key is overwritten with 0x00-Bytes.
  • The kernel only runs signed XBE files from allowed media.

There are also a handful of assumptions:

  • The CPU will start execution in the MCPX ROM.
  • The MCPX ROM can not be read or modified.
  • The decrpyted 2BL or Kernel can not be read entirely.
  • All parts of the software following the MCPX are not-attackable and signed.

See Exploits for possible options to break the chain of trust.

MCPX ROM

Certain things are still missing, for example, getting the CPU to 32 bit protected mode and enabling caching.[FIXME]

Xcodes

The xcode interpreter is common through both versions of the MCPX ROM. The high level interpretation of the MCPX ROM might look like this:

void xcode_interpreter() {

    // values are implied as x86 is just starting up
    register uint32_t pc        = 0; // stored in ESI register
    register uint8_t  opcode    = 0; // stored in AL register
    register uint32_t operand_1 = 0; // stored in EBC register
    register uint32_t operand_2 = 0; // stored in ECX register
    register uint32_t result    = 0; // stored in EDI register
    register uint32_t scratch   = 0; // stored in EBP register

    // explicitly set startup point
    pc = 0xFF000080;

    while (1) {
        opcode    = get_memory_byte(pc);
        operand_1 = get_memory_dword(pc+1);
        operand_2 = get_memory_dword(pc+5);

        if (opcode == 0x07) {
            opcode    = operand_1;
            operand_1 = operand_2;
            operand_2 = result;
        }

        if (opcode == 0x02) {
            result = get_memory_dword(operand_1 & 0x0fffffff);
        } else if (opcode == 0x03) {
            set_memory_dword(operand_1) = operand_2;
        } else if (opcode == 0x06) {
            result = (result & operand_1) | operand_2;
        } else if (opcode == 0x04) {
            if (operand_1 == 0x80000880) {
                operand_2 &= 0xfffffffd;
            }
            outl(operand_1, 0xcf8);
            outl(operand_2, 0xcfc);
        } else if (opcode == 0x05) {
            outl(operand_1, 0xcf8);
            result = inl(0xcfc);
        } else if (opcode == 0x08) {
            if (result != operand_1) {
                pc += operand_2;
            }
        } else if (opcode == 0x09) {
            pc += operand_2;
        } else if (opcode == 0x10) {
            scratch = (scratch & operand_1) | operand_2;
            result = scratch;
        } else if (opcode == 0x11) {
            outb(operand_2, operand_1);
        } else if (opcode == 0x12) {
            result = inb(operand_1);
        } else if (opcode == 0xee) {
            break;
        }

        pc += 9;
    }
}

RC4 Decryption of the 2BL (MCPX 1.0 only)

Version 1.0 of the ROM uses RC4 to decrypt the 2BL. The RC4 algorithm was included as part of MCPX 1.0 and seems to work fine with BIOS versions 3944, 4034, and 4134.

Stage 1: Key Scheduling

The RC4 Key-Scheduling Algorithm is used to initialize the RC4 “S” array, first initializing the identity permutation (writing 1, 2, ..., 255 to 0x8F000 to 0x8F0FF), then processed in a way similar to the PRGA to mix in the key.

uint8_t  *s = (uint8_t *)0x8f000;
uint32_t  i;

for (i = 0; i <= 255; i++) {
    s[i] = i;
}

uint8_t *key = (uint8_t *)0xffffffa5; /* ROM offset 0x1a5. */
uint8_t j, t;

/* It is unclear why values s[0x100..0x101] are being set to 0. They are
 * not modified by the code, but later these will be be used as the initial
 * i, j values in the PRGA.
 */
s[0x100] = 0x00;
s[0x101] = 0x00;

for (i = 0, j = 0; i <= 255; i++) {
    j = j + s[i] + key[i%16];

    /* Swap s[i] and s[j] */
    t    = s[i];
    s[i] = s[j];
    s[j] = t;
}

Stage 2: PRGA

The RC4 Pseudo-random generation algorithm (PRGA) is then used to decrypt the 2BL from 0xFFFF9E00, storing the decrypted 2BL at 0x00090000. It is 24KiB in size.

uint8_t  *encrypted = (uint8_t*)0xFFFF9E00; /* 2bl */
uint8_t  *decrypted = (uint8_t*)0x90000; /* Decrypted 2bl Destination */
uint32_t  pos;

/* As noted above, s[0x100..0x101] were set to 0 earlier, but have not been
 * modified since. The RC4 algorithm defines i and j both to be set to 0
 * before PRGA begins. */
i = s[0x100];
j = s[0x101];

for (pos = 0; pos < 0x6000; pos++) {
    /* Update i, j. */
    i  = (i + 1) & 0xff;
    j += s[i];

    /* Swap s[i] and s[j]. */
    t    = s[i];
    s[i] = s[j];
    s[j] = t;

    /* Decrypt message and write output. */
    decrypted[pos] = encrypted[pos] ^ s[ s[i] + s[j] ];
}

Stage 3: Signature Verification

Now that the Second-Stage Bootloader has been loaded, a quick sanity-check is performed: a “magic” signature is verified. If the signature doesn’t match, control goes to the error handler. If the signature does match, the code will jump to the 2bl entry point, which is given by the first dword of the decrypted 2bl.

mov  eax, [0x95fe4]
cmp  eax, MAGIC_NUMBER
jne  0xffffff94 ; If signature check failed, jump to error handler
mov  eax, [0x90000]
jmp  eax        ; Jump to 2BL entry point

TEA Decryption of the FBL (MCPX 1.1 only)

[FIXME]

FBL (MCPX 1.1 only)

The Flash Boot Loader was added in MCPX 1.1, it connects the MCPX ROM and the 2BL.[FIXME] It is not part of the MCPX ROM, but part of the flash.

2BL

[FIXME]

MTRR Setup

First, the cache is disabled.[FIXME] Then, the MTRR (Memory Type Range Register) will be setup (using wrmsr) in the following way:

MTRR (ecx) High value (edx) Low value (eax) Notes
0x200 0x00000000 0x00000006
0x201 0x0000000F 0xFC000800 (For 64 MiB RAM BIOS)
0xF8000800 (For 128 MiB RAM BIOS)
0x202 0x00000000 0xFFF80005
0x203 0x0000000F 0xFFF80800
0x204 0x00000000 0x00000000 Clear all unused MTRR
...
0x20F 0x00000000 0x00000000
0x2FF 0x00000000 0x00000800

Once the MTRR have been written, the cache is enabled.[FIXME]

Register setup

Now the 2BL will set up the segment registers[FIXME] and stack:

Register Value Notes
ds 0x0010 Data segment[citation needed]
es 0x0010
ss 0x0010
esp 0x00400000
fs 0x0000
gs 0x0000

Self-copy

Now the 2BL copies itself (24 kiB) from 0x00900000 to memory address 0x00400000.

Paging

Now a PDE is prepared at address 0x0000F000:

Offset in PDE Value Notes
0x000 0x000000E3 Identity maps the first 256MiB of RAM: 0x00000000 and 0x80000000 will both map to physical page 0

0xE3: Flags:
* 0x80: 4 MiB page
* 0x40: Marked as previously written (Dirty)
* 0x20: Marked as previously accessed
* 0x02: Read/Write
* 0x01: Present
0x800 0x000000E3
0x004 0x004000E3
0x804 0x004000E3
...
0x8FC 0x0FC000E3
0x0FC 0x0FC000E3
0x900 0x00000000 Unmapping the rest of the pages
0x100 0x00000000
...
0xFFC 0x00000000
0x7FC 0x00000000
0xC00 0x0000F063 Maps the PDE (4 kiB page) to address 0xC0000000

0x63: Flags:
* 0x40: Marked as previously written (Dirty)
* 0x20: Marked as previously accessed
* 0x02: Read/Write
* 0x01: Present
0xFFC 0xFFC000E3 Identity maps the upper portion of the Flash (4 MiB page) to address 0xFFC00000

0xE3: Flags:
* 0x80: 4 MiB page
* 0x40: Marked as previously written (Dirty)
* 0x20: Marked as previously accessed
* 0x02: Read/Write
* 0x01: Present
0xFD0 0xFD0000FB Maps 16 MiB for the GPU control registers

0xFB: Flags:
* 0x80: 4 MiB page
* 0x40: Marked as previously written (Dirty)
* 0x20: Marked as previously accessed
* 0x10: Cache disabled
* 0x08: Write-Through caching
* 0x02: Read/Write
* 0x01: Present
0xFD4 0xFD4000FB
0xFD8 0xFD8000FB
0xFDC 0xFDC000FB

After setting up the PDE, the PAT is set up using wrmsr: [FIXME]

CR4 is touched [FIXME]

CR3 is touched [FIXME]

Now paging is activated by enabling the PG and WP bits in CR0. Additionally, the same or instruction is used to enable the NE bit in cr0.

2BL main

esp is now also reloaded to point at the relocated address. It will be set to 0x80400000 (absolute value, independent of previous esp value). The 2BL will now call into the relocated 2BL code somewhere near 0x00400000.

Disabling of the MCPX ROM

out32(0xCF8, 0x80000880);
out8(0xCFC, 0x02);

SMC handling

The SMC has a watchdog functionality which must be turned off. This is done by querying the SMC registers 0x1C - 0x1F. If all of them are 0x00 the 2BL will shutdown the system[FIXME]. If this is not the case, the bootloader calculates the watchdog challenge response and sends it to SMC registers 0x20 and 0x21.

Additionally, the 2BL will set SMC register 0x01 to 0 (which resets the cursor position for reading the SMC revision information).

Enable IDE and NIC

out32(0xCF8, 0x8000088C);
out32(0xCFC, 0x40000000);

Memory cleanup

The 2BL fills memory with 0xCC from 0x80090000 to 0x80095FFF. These are the 24 kiB where the 2BL was stored previously.

Setup RAM timing

Not described yet, this is complicated[FIXME]. This got a lot more complicated when Microsoft started using different RAM sometime after Hardware Revision 1.6 was already out.

Weird stuff 2

This does some PCI config, use unknown[FIXME].

out32(0xCF8, 0x80000854);
out32(0xCFC, in32(0xCFC) | 0x88000000);

out32(0xCF8, 0x80000064);
out32(0xCFC, in32(0xCFC) | 0x88000000);

out32(0xCF8, 0x8000006C);
uint32_t tmp = in32(0xCFC);
out32(0xCFC, tmp & 0xFFFFFFFE);
out32(0xCFC, tmp);

out32(0xCF8, 0x80000080);
out32(0xCFC, 0x00000100);

Weird stuff 3

[FIXME]

out32(0xCF8, 0x80000808);
uint8_t mcpx_revision = in8(0xCFC);    

if (mcpx_revision >= 0xD1) {
  out32(0xCF8, 0x800008C8);
  out32(0xCFC, 0x00008F00);
}

Loading the kernel

Kernel-copy

The Kernel is now copied into RAM.

Kernel decryption

The 2BL will copy the kernel decryption key (16 bytes) from offset 32 of an array of 3 keys:

Offset Use
0 EEPROM key
16 Certificate key
32 Kernel key

The Kernel is then decrypted in-place using RC4.

Kernel decompression

The Kernel is decompressed directly to 0x80010000 where it will reside until a full system shutdown.

Running the kernel

The xboxkrnl.exe header at 0x8001000 is checked[FIXME]. If it is invalid, [FIXME]. If it is valid, the kernel entry point is looked up from the PE optional header. The hardcoded image base of 0x8001000 is added to the entry point. The entry-point is now being called. Argumnts are passed on the stack, from right to left. The first argument is a commandline string loaded from memory address 0x80400000. It is an empty string for retail BIOS[FIXME]. A pointer to the previously mentioned array of 3 keys is passed as the second argument.

Kernel

Initialization

Stage 1 (Cold-boot only)

The entry point to the kernel will first parse the arguments.[FIXME] At the end, the kernel will call the initialization routine for what we'll refer to as: Stage 2a.

Stage 2 (Cold-boot only)

The kernel initialization will only happen once on a cold-boot. It will not happen for reboots.

  • ebp is set to 0x00000000
  • esp is modified[FIXME]
  • GDT is prepared[FIXME] and loaded[FIXME]
  • cs and ds are reloaded
  • fs is set[FIXME]
  • TSS is loaded[FIXME]
  • cr3 is moved to 3 tasks[FIXME]
  • The CPU microcode is updated

After this comes Stage 3 initialization which will also be repeated on kernel re-initialization.

Stage 3

This is code which is duplicated in INIT and .text sections.

  • In the INIT section it directly follows the Stage 2 initialization.
  • In the .text section it follows the Kernel re-initialization code mentioned below.

This code does the following:

  • IDT is prepared[FIXME] and loaded[FIXME]
  • [FIXME]

Re-initialization

On reboots, initialization Stage 1 and 2 are not in memory anymore (as the INIT section has been discarded), and can't be run anymore. Instead, a seperate function replaces their functionality and then jumps directly to Stage 3 initalization.

This code is the partial kernel reinitialization, which will be ran on reboots using Kernel/HalReturnToFirmware.

  • ebp is set to 0x00000000
  • esp is modified[FIXME]
  • Some memory stuff in a seperate function[FIXME]
  • The .data section from Flash is loaded and replaces the running .data
  • The byte infront of KeSystemTime is set to 0x01, indicating the system comes from a reboot.

After this has completed, #Stage 3 of the kernel initialization will take over.

Skipped initialization

When rebooting, certain parts are still initialized and assumed to be working:

(This list is currently in no particular order and incomplete)

  • Anything already done by Stage 1 and Stage 2
  • PCI device setup
  • EEPROM decryption[FIXME]
  • Check for AV-Pack[FIXME]
  • Video mode setup (boot animation is not played again)
  • Some IDE stuff[FIXME]
  • Some SMC stuff[FIXME]
  • Memory allocator initialization[FIXME]
  • Kernel debugger (Super-I/O) initialization[FIXME] (This still seems to be in memory?!)[citation needed]

Startup animation

References